.. _broker-sqs: ================== Using Amazon SQS ================== .. _broker-sqs-installation: Installation ============ For the Amazon SQS support you have to install additional dependencies. You can install both Celery and these dependencies in one go using the ``celery[sqs]`` :ref:`bundle `: .. code-block:: console $ pip install celery[sqs] .. _broker-sqs-configuration: Configuration ============= You have to specify SQS in the broker URL:: broker_url = 'sqs://ABCDEFGHIJKLMNOPQRST:ZYXK7NiynGlTogH8Nj+P9nlE73sq3@' where the URL format is: .. code-block:: text sqs://aws_access_key_id:aws_secret_access_key@ you must *remember to include the "@" at the end*. The login credentials can also be set using the environment variables :envvar:`AWS_ACCESS_KEY_ID` and :envvar:`AWS_SECRET_ACCESS_KEY`, in that case the broker URL may only be ``sqs://``. If you are using IAM roles on instances, you can set the BROKER_URL to: ``sqs://`` and kombu will attempt to retrieve access tokens from the instance metadata. .. note:: If you specify AWS credentials in the broker URL, then please keep in mind that the secret access key may contain unsafe characters that need to be URL encoded. Options ======= Region ------ The default region is ``us-east-1`` but you can select another region by configuring the :setting:`broker_transport_options` setting:: broker_transport_options = {'region': 'eu-west-1'} .. seealso:: An overview of Amazon Web Services regions can be found here: http://aws.amazon.com/about-aws/globalinfrastructure/ Visibility Timeout ------------------ The visibility timeout defines the number of seconds to wait for the worker to acknowledge the task before the message is redelivered to another worker. Also see caveats below. This option is set via the :setting:`broker_transport_options` setting:: broker_transport_options = {'visibility_timeout': 3600} # 1 hour. The default visibility timeout is 30 minutes. Polling Interval ---------------- The polling interval decides the number of seconds to sleep between unsuccessful polls. This value can be either an int or a float. By default the value is *one second*: this means the worker will sleep for one second when there's no more messages to read. You must note that **more frequent polling is also more expensive, so increasing the polling interval can save you money**. The polling interval can be set via the :setting:`broker_transport_options` setting:: broker_transport_options = {'polling_interval': 0.3} Very frequent polling intervals can cause *busy loops*, resulting in the worker using a lot of CPU time. If you need sub-millisecond precision you should consider using another transport, like `RabbitMQ `, or `Redis `. Queue Prefix ------------ By default Celery won't assign any prefix to the queue names, If you have other services using SQS you can configure it do so using the :setting:`broker_transport_options` setting:: broker_transport_options = {'queue_name_prefix': 'celery-'} .. _sqs-caveats: Caveats ======= - If a task isn't acknowledged within the ``visibility_timeout``, the task will be redelivered to another worker and executed. This causes problems with ETA/countdown/retry tasks where the time to execute exceeds the visibility timeout; in fact if that happens it will be executed again, and again in a loop. So you have to increase the visibility timeout to match the time of the longest ETA you're planning to use. Note that Celery will redeliver messages at worker shutdown, so having a long visibility timeout will only delay the redelivery of 'lost' tasks in the event of a power failure or forcefully terminated workers. Periodic tasks won't be affected by the visibility timeout, as it is a concept separate from ETA/countdown. The maximum visibility timeout supported by AWS as of this writing is 12 hours (43200 seconds):: broker_transport_options = {'visibility_timeout': 43200} - SQS doesn't yet support worker remote control commands. - SQS doesn't yet support events, and so cannot be used with :program:`celery events`, :program:`celerymon`, or the Django Admin monitor. .. _sqs-results-configuration: Results ------- Multiple products in the Amazon Web Services family could be a good candidate to store or publish results with, but there's no such result backend included at this point. .. warning:: Don't use the ``amqp`` result backend with SQS. It will create one queue for every task, and the queues will not be collected. This could cost you money that would be better spent contributing an AWS result store backend back to Celery :)